Welcome to

Shenzhen Rakinda Technology Co., Ltd.

Official website!

Access Control System

Home > PRODUCTS > Access Control System
  • /uploadfile/image/20210312/20210312144059_3081.jpg
  • /uploadfile/image/20200812/20200812105932_4497.jpg
  • /uploadfile/image/20200812/20200812105938_4184.jpg
  • /uploadfile/image/20200812/20200812105945_4027.jpg
  • /uploadfile/image/20200812/20200812105950_9808.jpg
RD008 2D IC Card Reader Access Control Machine with qr code scanner

Category:Access Control Solution

Product ID:


Product Introduction:Single door network access control + QR code scanning head +IC card reader triple product. Make the on-site installation and maintenance simple and cost-effective.

Inquiry Now


Nowadays more and more Residential area, office area, factory using the access control device for managing the visitor visit. As it is more intelligent and more convenient. Our RD008 NFC 4G WIFI QR code scanner access control system can read both Mifare card and QR code to get access. Its reading card region is very wide and can read card even in 20mm.

Features of Mifare Door Access Control
1.Embedded multi-tasking real-time operating system, the system can be fully started in 3 seconds.
2.Single door network access control + QR code scanning head  +IC card reader triple product. Make the on-site installation and maintenance simple and cost-effective.
3. The product comes with a voice amplifier and speaker. The voice for common entry and exit events can be set. The network can control nearly 150 voices and can customize the voice.
4. Encrypted QR code that complies with the agreed rules can be opened / opened directly when not connected to the Internet.
The agreed rules mainly include: 
(1)the start time and end time of the two-dimensional code valid; 
(2)the number of times the two-dimensional code is valid and exceeds the number of uses, the two-dimensional code can no longer be used;
(3)equipment MAC matching or project number building number Match, a QR code can contain one or more device numbers, which can be legally valid on multiple devices;
(4)The encryption key of the QR code can be modified without leaving any backdoors or loopholes to ensure the security of the QR code.
5. Common parameters such as network IP parameters, lock delay, Wiegand 26/34, etc. can be set directly through the QR code, making site commissioning easier.
6. Equipment capacity: 35,000 cards, 50,000 records, 100,000 QR codes, and records and QR codes exceeding the capacity will be automatically covered.
7. The product adopts the battery-free clock holding circuit, without batteries, eliminating the need to replace the battery regularly, and the trouble of express delivery.
8. The product adopts data storage and ferroelectric storage. Even if the device is suddenly powered off, the stored data will not be lost, ensuring data security and reliability.
9.  The product can read ISO14443A type card serial number or sector content, such as M1 card.
10.The network transmission standard is RJ45 10 / 100M TCP / IP transmission, which can be extended WIFI transmission or mobile phone Bluetooth transmission.
11.Supports TCP / IP networking connection across gateways and network segments, and direct-connected network cables and cross-network cable controllers can automatically adapt.
12.Built-in dual hardware anti-crash watchdog, even if the chip runs abnormally, it can be recovered in time without affecting the use.
13.Support TCP / IP remote IAP upgrade. If there is a change in requirements, after modifying the program, it can be completed directly through the network upgrade.
14.The WIFI module can be extended to enable the two-dimensional code to be transmitted over the wireless network through WIFI. The WIFI module supports AP and STA dual modes.
15.The Bluetooth module can be extended to enable the product to communicate with the mobile phone's Bluetooth. Achieve functions such as shaking the door.
16.Integration of the development kit with the DEMO language: JAVA, C #, C++, etc.

QR Code Reader Access Control Parameters

RD008 Round 2D IC Card Access Control Machine-datasheet

RD008 Round 2D IC Card Access Control Machine

QR Code Scanning Component Parameters

Image Sensor


Light Source

White LED


2D: PDF417, QR CODE, DATA MATRIX,Support Mobile Phone Mirror Recognition and Paper 2D Code Recognition

1D: CODE 128, UCC/EAN-128, AIM-128, EAN-8 etc.

Reading Distance


Scan Angle

360° Full Angle

Display Components


1.8 ”TFT true color screen


128 * 160

Display Area


Input and Output Parameters

Power Input


Working Current

< 600mA

Can read like ISO14443Aor ISO14443B Card Serial Number

Such as Second-generation ID card, FM1208 CPU Card, M1 Card (Mifare S50, Mifare S70 IC card), SRIX4K, etc.

Barcode or 2D Code Input

Wiegand 26/34 output, output IC card number (common read head function) and associated card number output in compliance with QR code reservation rules

Communication Interface

RJ45 10/100M TCP/IP, Extensible Wireless WIFI, Bluetooth,4G(Options)

Communication Protocol

Support TCP / UDP / HTTP

Voice output

comes with voice, amplifier and speaker output, nearly 150 kinds of voice output, customizable voice

Device Input

12V DC power input, 1 door magnetic input, 1 door button input, 1 alarm input

Equipment output

1 channel 3A relay output, 1 channel unlock, 1 channel expansion can control door opener, light, water valve, etc.

Wiegand output

Wiegand 26/34 output


Installation size

110mm * 25-34.62mm (L*H), Compatible with standard 86 box

Contact Us:

If you want to know more information? Please fill in the following message form, we will contact you in the first time.

(We will never, ever spam you – nor sell, trade, or transfer your email to anyone else.)

Related Products:

Tech Support